How to change an alternator on a 1989 Oldsmobile 98 Regency?

Does anybody know how? The original owner didn't even take care of the manual so I don't know how to locate anything in the car it's torn apart :/How to change an alternator on a 1989 Oldsmobile 98 Regency?Disconnect the Negative battery cable.



Loosen the pivot and slot bolts on the alternator, and remove the belt.



Remove the bolts the rest of the way, then remove the wires from the alternator. Or remove the wires first, if you can get at them.



Install in reverse order.How to change an alternator on a 1989 Oldsmobile 98 Regency?1. Take off the old one



2. Install the new one



For more detailed info, visit a library, go to Autozone.com or buy a repair manual.

myspace pictures

how to use floppy disks

I have a saab 900 ems 1989 car, i changed alternator but it still not charge,what else could be wrong?

i have 1989 saab ems, when the charge light is on,the car sudden stoped,RACV people said it was alternator fault,,later i changed alternator,it was second hand one from volvesaab parts,when i put replacement ,i start the car,the charge light is still on,i checked battery, it i was not charged, can anyone who is expert on the saab tell me what else could be wrong? i checked alternator drive belt,i think it is correctly tensioned.

so if the replacement of alternator is also deflective,how can i check whether is alternator problem or voltage regulator problem, because i have three month warrant .so i have to make sure it is alternator problemI have a saab 900 ems 1989 car, i changed alternator but it still not charge,what else could be wrong?Look at the alternator for a wiring connection marked field,or f1.Check it with a test light or volt meter to be sure it is energized when the ignition is turned on.If it isn't,there may be a fault with the circuit and it may be fused.If it checks out,the next suspect is the regulator which should be checked for poor connections or replaced.You can find out if the charging system is working by briefly disconnecting the battery with the engine running.If it continues to run,the system is OK,if it dies,the charge system is dead.I have a saab 900 ems 1989 car, i changed alternator but it still not charge,what else could be wrong?well to check your alternator the first thing you can do is get yourself a mutimeter ( they are around 10 bucks from a electronic store) then while the car is running switch the mutimeter gauge to Volts then connect the positive(red) lead to the positive on the alternator (there should be a + sign) and the

black lead on the mulitimeter to the body of the alterantor to get a good ground.



if the meter reads over 13.1 volts then the alternator is good if not then the magnets inside the alternator may be worn down or the alternator coil may be broken.



its sounds to me as though you may have a charging system problem, if the battery is good then there could be an open in the charge system somewhere, auto electrics are best for finding faults like this since they have all the equipment at hand...goodluckI have a saab 900 ems 1989 car, i changed alternator but it still not charge,what else could be wrong?On some designs the voltage regulator is built into the alternator, and on others it is a separate module, often mounted somewhere on the inside fender well. A bad voltage regulator could cause your problem, as could a dead short.

Does anyone know how to change an Alternator belt for a 1998 Rav4?

I'm at work and my 1998 Rav4's alternator belt just snapped when i got back from lunch. I purchased the belt already but I'm not quite sure how to replace it. I was told there is a Tensioner pulley somewhere that I can turn to release some tension but I'm not sure which one it is. If you have a how-to or diagram or any information please help. ThanksDoes anyone know how to change an Alternator belt for a 1998 Rav4?Theyre not hard to replace but you are going to need a wrench to retract the belt tensioner. There is a diagram usually under your hood for the belt route. but the tensioner pulls back off the the belt so there is slack on the belt so you can pull out the old one and slip in the new one being sure to follow the same route as the old one. The only problem is your going to have to get yourself a wrench to do this.



heres a pic of one



http://www.amazon.com/Summit-SUM-900035-Does anyone know how to change an Alternator belt for a 1998 Rav4?It requires a serpentine belt tool. first take note of the routing of the belt, raise the car up and remove the shield covering the crank pulley, put a 19mm socket on the tool, find the tensioner toward the top of the engine, put the tool on the fixed tensioner casting (its a 19mm hex cast right into the tensioner) (do this from the bottom) and pull down. this will take the tension off the belt and allow you to slip the belt off the waterpump pulley. let the bar go back up and the whole belt will fall off. replacing is reverse, its tricky the first time......even the second or third. good luck! oh and dont try to drive it to the repair shop if you cant get it back on.....the waterpump wont be working so you'll risk engine damage by overheating, the power steering wont work, the battery wont charge, and as if it matters...the A/C wont work either!

How do I change the alternator on my 98' mustang?

I have a 3.8L v6 Mustang and I was hoping someone could post a %26quot;how to%26quot; or a %26quot;step by step%26quot; to help me out with changing my alternater! It shouldn't be to difficult, I would just feel better havign something to guide me along the way!



Thanks alot!How do I change the alternator on my 98' mustang?step 1 purchase alternator stepunhook battery from cable 2 remove alternator belt by pulling on the tenioner step 3 remove 2bolts from altinator step 4 remove wiring clips that go on step 5 theres usually will come with connections which u have to snip the old one and hook them to the stuff provided step 6 hook everything back up same way it came apart make sure your battery is charged then hook cables back to the battery then start vehicle . then if u dont have alt tester take positive cable unhook it from battery and if it stays then it is chargingHow do I change the alternator on my 98' mustang?if no one can help you go to autozone and ask for a book on your car it will show you every bolt, screw and wire to disassemble and rebuild your rideHow do I change the alternator on my 98' mustang?Take it to a mechanic unless you are mechanically inclined. Otherwise you have to disconnect the neg. battery cable, loosen the belt tensioner, remove the belt, disconnect the wires on the back of the alternator, label the wires, remove the bolts, and put the new one in in reverse order. Good Luck!How do I change the alternator on my 98' mustang?go to auto zone or one of the big chains they can sell you a manule on your specific vehicle they will have step by step and pics to help you do it your selfers get er done they will even tellyou what tool you will need to do the job good luck its easy and fun

How do I change the alternator fuse in my 1998 Mercury Villager?

I know where the fuse is. The problem is that I'm having a hard time pulling the old fuse out so I can put in the new one. Maybe I'm doing something wrong - is there a technique to pull the old fuse out? Any Suggestions?How do I change the alternator fuse in my 1998 Mercury Villager?you need a fuse puller, there might be one in the cover or pick one up at the parts store

How to change an alternator on a 2000 focus?

I have removed the two bolts that hold it on and it still don't want to come off. Is there another bolt or something?How to change an alternator on a 2000 focus?sometimes there is a brace on the back of the alternator..get in there w a flashlight and have a good look....



make sure u undid the neg batt terminal first...then undo the wiring to the alternator..



THEN take it off...



make sure you test your battery too....and replace your belt. if the battery is bad, it will ruin the new alternator. a slipping belt could also cause u problems..Peace.

home theater

good property for sale

How to change an alternator on a 1997 ford thunderbird?

If it has the 4.6



http://www.autozone.com/az/cds/en_us/090



no guide listed for the 3.8How to change an alternator on a 1997 ford thunderbird?find it losen the bolt take off the belt then take the bolt out take off the alternatorHow to change an alternator on a 1997 ford thunderbird?1. Look it up in your repair manual (or buy one)

2. Remove Belt

3. Remove alternator bolts or whatever is holding it on

4. Remove wires.

5. Take alternator out.

6. Put new alternator in

7. Plug in wires

8. Bolt on

9. Put belt back on

10. Start Cruising!!! :)



--This is a very easy thing to do. If this wasn't enough detail for you, just go look it up in your repair manual.How to change an alternator on a 1997 ford thunderbird?No one said to disconnect the battery. That is the first thing you do.Neg. first and reconnect last.

How do you change an alternator 98 jeep?

Bought a used Alternator now im tring to switch them outHow do you change an alternator 98 jeep?Used? Unless it has less than 20,000 miles on it, I would seriously reconsider getting a new one.

How good is your battery?, If you are going to use the battery that went with your old alternator, then I would suggest you get a new one, otherwise you could kill both the battery and the alternator.

Because you have a Jeep, the alternator is conveniently located in front of you when you open the hood.

Because I don't have all the numebrs in front of me, i will suggest going to an online repair manual or going to your library and renting one. In there, it will tell you how to change out the old and install the new.

How do you change the alternator in an 01 Volvo V70?

My boyfriend is trying to change the alternator and it is like nothing he has seen before. He thought he had to jack the engine, but that didn't work. He is stuck and does not know what to do.How do you change the alternator in an 01 Volvo V70?1. disconnect the negative battery cable [lay a rag over the battery post to prevent accidental arcing.

2 remove serpentine drive belt [make a drawing of belt routing before removal] now remove belt tensioner.

3 remove power steering fluid supply hose from pump [catch fluid from resivour in a pan and dispose of properly][you will need approx a bottel and a half of NEW fluid upon reassembely]

3-a at this point disconnect the top radiator hose from engine and lay aside [about 2 quarts of coolant will be lost]

4 remove the pressure line from the pump and lay aside [cover open end with another rag to prevent dirt entry] now unbolt and remove the pump.

5 note the position of wires on back of alternator [don't remove just yet]

6 the alternator %26quot;nests%26quot; between the a/c compressor and the engine block. so remove the top 2 compressor bolts, then loosen but DO NOT

remove the bottom 2 compressor bolts.

7 now remove the one bolt at the top of the alternator, [this is a little tight to fit hand there]

8 pull alternator towred the fnt. of car and upwards at the same time, all while twisting enough to expose wiring, whitch can now be disconnected.

9 now pull alternator out from the top.

10 while installation is the reverse of above leave the battery feed wire a little loose [the big red wire] until new alternator is securely mounted

then this can be tightened after wire is back in guide groove [don't forget to reinstall the wire cover, it just snaps in place]

11 fill p/s resivour and coolant resivourto mark [leave coolant cap off so pressure wont build up and scald you]. before starting.

let warm at idle until cooling fans come on and recheck the coolant level, adding as necessary then replacing the capHow do you change the alternator in an 01 Volvo V70?I don't think you can do this yourself.

You are able to take it out, but if you change it, you need software for the new alternator. So the new alternator wouldn't work properly.

Need to change a ALTERNATOR 1991 Honda Accord?

Please tell me how to change a alternator? I am a single mom and can not afford to pay for labor cost. So I will be changing this myself. I do not know where to start andd what tools I need. Please help me out I am desperate. Thanks, I really do appreciate it!Need to change a ALTERNATOR 1991 Honda Accord?I don't know why you are changing the alternator. unless the charging system light is on it could be other problems.



if you want the step by step instructions send me an email and include your regular email address in that email and I'll send them to you.



to email me click on the icon above my name to the left of this response then select 'email' from the right side of the profile box. be sure to include a regular email address in the text of the message so I know where to send it. Yahoo Answers will not allow attachments to answers. doing it this way keeps your email address and mine out of the searchable Yahoo Answers database



hope that helpsNeed to change a ALTERNATOR 1991 Honda Accord?Honda Guy knows his stuff. He is your best source.

How to change a alternator belt plus a power steering and air conditioner belt?

i have a 1994 kh ford laser and 1.6 carb and need to change the belts and i do not know how to take the tension off the power steering/ air conditioner beltHow to change a alternator belt plus a power steering and air conditioner belt?On the power steering directly below the pulley and to the front of the car is the tension screw for the air conditioning and power steering belt. Approximately 2 inches back from that screw is the locking nut for the tension screw, this one is tricky to get to as the pulley may be in the road. Loosen this nut and that will allow you to loosen the tension on the belt.How to change a alternator belt plus a power steering and air conditioner belt?On one of the pulleys you put a 18m socket (long socket) and there's a Bolt on the pulley just turn it one way or another and that will relieve the tension,



Now the 18m was for a ford Taurus

How do I keep my comforter fluffy

official myspace

How much to change an alternator on my truck?

i've got a 98 tacoma that needs an alternator. the part itself is 140. how much could i be looking at payin?How much to change an alternator on my truck?you can change it your self it is very easy just need a simple tool set and you can change it in 25 min.How much to change an alternator on my truck?have someone you know who's good with cars oput it in for 20-30$. amechanic could be from40-80$ be my guess;)How much to change an alternator on my truck?Changing an alternator is rather simple. I would suggest buying a manual and doing it yourself. Plus, the manual will assist you in any future repairs. Will save you $.



I attached a direct link to Haynes, a supplier of manuals.

How long should it take to change a alternator on a 2003 yukon xl, 5.3 liter engine?

my battery not charging light has come on the display, I had the alternator checked and it showed that it was right above the weak signal strength. Would I need the tension tool to take the serpentine belt off?How long should it take to change a alternator on a 2003 yukon xl, 5.3 liter engine?Yes you need to release the tension, but a wrench will work.



That job can be done in 15 minutes or less if you know how.

How do you change a bmw alternator belt?

I have a 2000 BMW 740i and I need help changing the alternator belt. I took it to a local mechanic and they took everything apart and do not know the alternator belt configuration. Any help is appreciated. thanks so much =]How do you change a bmw alternator belt?BMW cars do NOT cost any more than other cars to own, REALLY. Wear items like belts, brake pads, and rotors are very cheap in comparison and will outlast other similar parts from other car-makers, generally. Your problem will always be finding someone who charges a decent repair wage for labor. Labor is nearly ALWAYS more. THere should be a map of belt routing under your hood or in your owner's manual. GOOD LUCK!! IT should be easy!!How do you change a bmw alternator belt?bmw are exspencive cars to own i have a 325i and it cost me a lot just for the simplest things. You need to take it to a dealership or a michanic that knows bmw but just be warned its gonna be $$$$$$

How to change the alternator on a '96 Nissan Maxima?

I have a bad alternator does anyone have a diagram on how to remove it or can I get step by step instructions?How to change the alternator on a '96 Nissan Maxima?the alternator is usually held on by a couple of bolts. All cars are different, so all I can give is a general idea of the steps involved. To get detailed instructions, you need the service manual.



The first thing you should do is disconnect the battery



Then, follow the instructions for loosening and removing the belt from the alternator.



Unplug or unscrew all connections to the alternator



Remove bolts securing the alternator to the motor.



Remove the alternator and replace following the instructions in reverse.



Looking at pictures of the motor, it looks like the easiest way to get to the alternator is from under the car. It looks to be on the passenger side near the front of the car

How do i change the alternator on a fiat punto 1.2?

My Fiat Punto 1.2 didn't start one morning,someone looked at it and said its the battery.I changed it and it worked for few days and then it died again.The only logical solution is to change the alternator but i don't want to go to a mechanic because i'm already short on cash.Can someone please explain how i can change it myself?How do i change the alternator on a fiat punto 1.2?On the 1.2 Punto engine, the alternator is located at the rear of the engine, furthest from the gearbox. The alternator pivots on one mounting and has a second mounting which tightens to tension the belt. Access is easier with the roadwheel and wheelarch liner removed (simply screwed in.) Disconnect the battery and slacken all the mounting bolts for the alternator. This will loosen the belt so it can be removed. Disconnect the wiring connectors from the rear of the alternator and then remove the alternator all together. Replacement is the reverse of fitting, but i would recommend a new belt at the same time - if the old belt snaps, it can rip off the cambelt aswell which is not good news! To tension the belt, use a pry bar to push the alternator away from the engine and tighten the belt. Hold this tension as you tighten up the top mounting nut which will then keep the tension.How do i change the alternator on a fiat punto 1.2?disconect the battery but before you do make sure you have the radio code,remove the wire`s attatched to the alt/unit take the bolts off that secure the altinator,refit in reverse order.

hair clips

if you wonthelottery

How do I change the alternator of a 95 pontiac gand am?

the engine is a V6, i just need to know how to change it without takeing the whole engine apart.How do I change the alternator of a 95 pontiac gand am?it should be pretty easy on the car, the motor is either a 3.1ltr or the 3800 and the alt should be on top and in the middle. Take the neg bat cable off and then take a three eights drive ratchet and turn back the belt tension er and undo the belt and then undo the plug to the alt and then take out the two bolts and presto new back in same order but reversed.How do I change the alternator of a 95 pontiac gand am?your engine will be a 3100, changing the alternator is a little hard

to do the first time but here goes. most belt tensioners take a 15mm wrench to take the tension off the belt. it will be hard to remove the tension without a special or long end wrench but it can be done. then remove the belt from the alternator, there is a large red wire attached to the alternator and 2 or 3 smaller wires the plug into it. you might have to have a %26quot;back up%26quot; wrench to remove the nut on the red wire, they often turn inside and ruin the alternator. there are 2 bolts that hold the alternator in its brackets

and a smaller bracket on the back side with a bolt in the alternator and a nut onto the top of the motor. it is a 15 minute job if you have the tools and have done it before.How do I change the alternator of a 95 pontiac gand am?disconnect the shiz and connect the shiz man.How do I change the alternator of a 95 pontiac gand am?You may need a special wrench designed for releasing the tensioner assembly so you can remove the belt. Once you accomplish this, it's pretty straight forward. First, disconnect the battery! Proceed with the belt, and move on. Two or three bolts, depending upon the design of the bracket, and the whole thing will lift right out. Take it with you when you purchase the new one. There are 4, yes 4 different locations for the wiring connections. This is known as %26quot;clocking%26quot;. It is much easier to get the correct one the first time, but, if you need your ride right away, and your local auto parts store doesn't have the proper one, you can do this yourself. If you have an impast wrench, spin the pulley loose. Don't remove it yet! Turn it up, nose down, on a table or workbench. You need to take the three bolts loose that keep the housing together. Do NOT, under ANY circumstances lift the alternator up from now on. If you do, no sweat, but this isn't alternator rebuild 101. With the nose of the alternator on the table, take the three bolts out. Tap on the front portion of the housing and it will drop down. Spin it so that the mounting holes and the harness connections are in the correct location and re-install the three bolts. You will have to tighten them in sequence otherwise it may cause the armature to bind. I've done thousands of them. It will take you about 15 minutes to clock it if you have to.

How do I change the Alternator for my 1997 Dodge Neon?

My brother changed my alternator a few weeks ago, and its already giving me problems, when I took it into the shop, they said it was a dud. I can't get him or anyone else to fix it this time, so I have to do it myself, I just cant figure out how to replace it this time. It has a full lifetime warranty, so I don't want to take it to a shop.How do I change the Alternator for my 1997 Dodge Neon?It's easiest on a hoist but if you can't get to one, jack up the right front and turn wheel all the way to the left.

-disconnect negative cable from battery

-remove right wheel

-remove splash guard

-on top of alternator there is a belt tension adjusting nut, you'll have to loosen the tension on the belt ( this is the hardest part due to the lack of space ) in order to remove the belt

-there is a bracket that holds the alternator ( held by 2 or 3 bolts ), this has to be removed

-with bracket gone, the alternator can come out but the space is very tight...you may have to turn the alternator at different angles to be able to squeeze it past the wheel well area



-

How do I know if I need to change the alternator, alternator belt, battery or all of the above?

I have a 1990 Toyota Camry that runs fine but doesn't like to get started. It turns right on when you jump it and before that the lights work fine. So I don't think it's the battery. How do I know if it's the alternator or just the belt? Appreciate any help.How do I know if I need to change the alternator, alternator belt, battery or all of the above?Take a multitester and measure battery voltage it should read 12 volts. Then start the car and measure voltage at the battery again. It should be ideally 14.4 volts but 14 range is good. If the voltage on the battery is drastically under 12 volts the suspect is the battery. if it is under 14 then it is likely the alternator or the voltage regulator, or even a loose alternator belt as stated. If you do not have a multitester you can go to a checker shucks cragan and have them check the battery and alternator, they will test them for free. Another thing to check is for your battery cables and terminals to be in good shape tight and clean. i hope this helps.....How do I know if I need to change the alternator, alternator belt, battery or all of the above?Auto zone will test your alternator and battery for free ( perk of their biz to bring in customers ) If it runs fine when its already started then the alternator is working, if it doesnt hold a charge or has a hard time turning over and starting then its the battery. the belt wont affect any of these unless if it was off but you can look at it and see if its worn ( any fread edges or missing peices) How do I know if I need to change the alternator, alternator belt, battery or all of the above?If you are saying that if you jump it it will starts right up, then one of two things are bad.....battery or starter. If the battery is up to power then I would start looking at the starter. If the battery can't hold a load the look at the alternator or battery. Good Luck.How do I know if I need to change the alternator, alternator belt, battery or all of the above?Run the car at night with the headlights on. Then rev the engine, if the lights brighten and dim with the revs, its the alternatorHow do I know if I need to change the alternator, alternator belt, battery or all of the above?possibly a dead cell in your battery so now your pushing 10 volts instead of the 12 you need. almost every parts store will test the battery for free. How do I know if I need to change the alternator, alternator belt, battery or all of the above?You can take the battery and alt. to Auto Zone and have them tested they do this for free.How do I know if I need to change the alternator, alternator belt, battery or all of the above?if it stays running after the jump or boost then its the altenator...if it dont then its booth..either way go for them battery and alt...

How difficult is it to change the alternator on a Nissan Maxima?

my 2001 Maxima needs an alternator and I do not want to pay the high price of a mechanic when I may be able to do it myselfHow difficult is it to change the alternator on a Nissan Maxima?http://forums.maxima.org/



best place for advice as from def owners.

howtoendarelationshipwithsomeon

Long Goldfish

How do I change the alternator belt in an 87 Suburban?

The old one snapped while driving. Will I need a belt tensioner? It shouldn't be too hard, but I can't figure out what I need to loosen to get the new one on. Will I need to remove the fan belt to get the alternator belt on? Any advice would be really helpful.How do I change the alternator belt in an 87 Suburban?I get a kick out of these kids who think that every vehicle ever made has one single Serpentine belt. They probably couldn't adjust a set of points if they were stranded in the Yukon and their life depended on it.



You will need to remove any belts that are mounted in front of the Alternator belt. As far as the Alternator, those are easy. There are 2 bolts holding it in, one short one, and one long one, The long one is the one the Alternator pivots on. The short one keeps it from pivoting by locking it in place, although both should be tightened when you are done. Just loosen both, and push the Alternator towards the engine.



You probably have at least a Power Steering belt in front, and usually if you have Air Conditioning, that will be in the back on yours, if I remember correctly. Either of those are usually a little more complicated, as they have more than 2 bolts you have to loosen. The Power Steering has one on the back (a nut actually) that a lot of people don't notice.



Here are some pictures that might help;

http://www.autozone.com/images/cds/gif/m

http://www.autozone.com/images/cds/gif/m



Notice that the Power Steering has 3 bolts right in front of the pump, but those hold the pump to the bracket, so leave those alone. You want to loosen the 2 nuts/bolts towards the engine side, that hold the bracket to the engine, and the one in back, and move the pump and front bracket at the same time. The back bracket doesn't move like the front one does.



To get the belt off all the way, you will have to get it over the fan, which is easiest if you start on one side of the fan, and work your way towards the other side of the fan, one blade at a time. Put the new belts back over the fan the same way, except in reverse.



Once you get all the belts in place and on the pulleys, you need to move the device back away from the engine to tighten the belt. Be careful with the Power Steering especially, when using a pry bar, as the outside is the fluid reservoir. That bends easily, and can cause a leak if you do bend it.



Once you get the belt tight enough, tighten one of the lockdown bolts, which are mounted over a slot. Then tighten the rest, including the pivot bolts. Start the engine up, making sure that no one else is standing by the front of the car, and make sure they're still on and tight after you shut the engine off.How do I change the alternator belt in an 87 Suburban?You don't need to loosen anything. There should be a drawing of the belt route on the fan shrout. It should have picture of where the belt go. All you need is 3/4%26quot; socket and a long breaker bar.



1. You route all the belt to all the parts it is suppose to, power steering, a/c, alternator, main pulley, smog pump and of course the tensioner is last.

2. You stick the socket on the tensioner bolt and pull onto it while placing the belt over the tensioner.



Once the belt is on the tensioner, you are done! Making sure the belt go onto the other part properly. You can then start the engine.How do I change the alternator belt in an 87 Suburban?you only need a new belt tensioner if the old one has no tension on it or it vibrates too much when the engine is running, you will need either a 3/8 or 1/2 breaker bar, the tensioner arm will have a square hole to place the bar socket into, use the bar as a lever to slide the new belt in.

How to change a alternator on a 1995 chevy g20 van 4.3 engine size?

How to change a alternator on a 1995 chevy g20 van 4.3 engine size?How to change a alternator on a 1995 chevy g20 van 4.3 engine size?I agree pick-up a manual, it is a very straight forward job. I would like to have a dime for every alternator I have changed on full size vans. Ford, Dodge, or GM.How to change a alternator on a 1995 chevy g20 van 4.3 engine size?The alternator is fairly easy to change. I would suggest you buy a Haynes manual. It will best explain how to do it step by step with photos. They run about $15 and it's your best bet.

Anyone know how to change the alternator on a 1998 cavalier?

My son's car broke down. The battery is one year old. I didn't even open the hood yet. I just want to know where it is and if there is anything I should be aware of when changing the alternator. ThanksAnyone know how to change the alternator on a 1998 cavalier?V6, Alternator is on back side of passenger side of engine. Remove negative battery cable, Release belt tension at automatic tensioner. Remove upper metal bracket over alternator. this bracket will have 2, 8 mm bolts into alternator. after bracket removed one lower bolt goes through alternator. this bold has a nut on the back side and is difficult to get out. But it can be done. Someone put it in there. you can get it out. After bolt is removed you can rotate the alternator to gain access to electrical connectors.



4 cyl Alternator located passenger side front if engine. Remove negative battery cable, Remove metal bracket from exhaust manifold, remove lower through bolt and rotate alternator to gain access to electrical conectors.Anyone know how to change the alternator on a 1998 cavalier?Routis is right about the location.but to avoid serious damage remove the positive cable from the battery. then when you reconnect wait five minutes before starting. This allows the computer time to reset.Anyone know how to change the alternator on a 1998 cavalier?It is probably on the passenger side of the car near the bottom. Only thing you should be aware of is that there will probably be little room to work to replace it. Might be easiest to get at it from under the car.

How do I change the alternator belt on my 1999 Laguna sport?

Before anyone says it I know its a sh1t car but I like it, unfortunately though the alternator belt needs replacing %26amp; I dont know how to do it, can anyone tell me in complete idiot terms. Also it has air con if this has any bearing. I will be eternally grateful.

ThanksHow do I change the alternator belt on my 1999 Laguna sport?1 you need to take off the wheel engine side (jacked up)

there is an inner wing cover you need to remove

make a note of how the belt goes around the system (it will be a maze if you dont)

slaken tentioner pull belt off %26amp; replace in reverce order.How do I change the alternator belt on my 1999 Laguna sport?Go to autozone.com, get directions (with pics) there. Follow them. You can do it if you have the proper tools.How do I change the alternator belt on my 1999 Laguna sport?the alternator will have a slide on it you need to loosen the bolt clamp and slide the unit to loosen the belt it should easily come off. then you need to replace the belt with a new one and tighten the belt until it allows for 1 inch deflection as in when you press it with your finger

that should help. as for the a.c. bearing all pulleys like that have oneHow do I change the alternator belt on my 1999 Laguna sport?personally, i have know idea what mad mike has said!. if you have no mechanical experiance please take it to a garage. there could be 6 seperate pulleys, you do not want to be guessing after the belt is removed!.

How do i change the alternator in a 1.2 opel corsa b?

the alternator in my corsa has stoped working. I went and got a replacement yesterday but now i need to no how to change it. I have an idea but i need helpHow do i change the alternator in a 1.2 opel corsa b?Battery to be disconnected.



Mounting bolt and nut to be removed usually they are 17mms

Tensioner to be removed usually they are 12 or 11mms.

Wires from alternator to be removed usually 10,8 and 12mms connections.

bird

find an interesting online

How difficult is it to change an alternator in a Ford Explorer?

Assuming it is my alternator that needs to be replaced (clicking noise, won't start) I'd like to do it myself. Can someone give me a rough idea of how much it might cost and possibly walk me through it. Thanks.How difficult is it to change an alternator in a Ford Explorer?I would listen to the SVO dude. I had a 96 ranger with a bad alternator. What mine did is the battery light kept flickering while I was driving down the highway. I just put a used one in mine. If it was the alternator you could just replace the regulator on the alternator it's usually the brushes in side just get worn.



I doubt it's your alternator though. Probably a battery problem. Corroded cables can cause a lot of problems as well. You can clean them with baking soda and water.How difficult is it to change an alternator in a Ford Explorer?It's only a hour job, but before doing that, try charging the battery, have it checked too, and clean the posts and cables real good with a wire brush. Before actually buying a alternator have the old one tested..How difficult is it to change an alternator in a Ford Explorer?Look in your manual to see if your car has a tensioner for the serpentine belt, it will also tell you how to use the tensioner to remove your belt. If you don't have a tensioner, you will just need to take your belt off after you loosen the alternator.



On your new alternator, try and find where all the bolts seem to go in. Then find them on your installed alternator, all you have to do is pull all the bolts out, then put the new alternator in There will also be a place where the wires plug into the alternator. You will get greasy doing this, but it should take no more than an hour and a half.How difficult is it to change an alternator in a Ford Explorer?sounds like a battery or a connection issue not alternator, clicking noise usually means one of these unless your battery light was on before it would'nt start

How difficult is it to change the alternator on a 2002 dodge stratus?

I'm not even sure it's the alternator that's bad. Yesterday, I went out to start the car and it wouldn't turn over, just made a slight clicking noise. Got a jump, the car started, but, when I turned it off after about 30 minutes of running, it wouldn't start back up.

Don't want to have to spend a mint to fix it? My dad said he could fix it if the alternator is easy to get to. Any advice at all would be appreciated.How difficult is it to change the alternator on a 2002 dodge stratus?It would be best to have the Battery load-tested, check voltage while running, and check over the wiring connections to be sure. It's possible that the Battery is just not holding a charge. If the system voltage is above 13 with the engine running, you probably need a Battery.



If it is the Alternator that's bad, how hard does vary between engines. Here's instructions for your model, and the various engines. There's also a section on testing, but you'd need some electrical testing equipment.



http://www.autozone.com/shopping/repairG



Click the pictures to enlarge.



Whatever you do, don't disconnect the Battery while the car is running. I'm surprised some Bozo hasn't suggested it already.How difficult is it to change the alternator on a 2002 dodge stratus?I wouldn't just throw parts at it. Get it running and take it to a shop, or the professionals at auto zone if you'd like, and have a charging system test done.How difficult is it to change the alternator on a 2002 dodge stratus?it depends on what engine it has in it,that will determine how easy or hard it is to get to and remove,good luck,How difficult is it to change the alternator on a 2002 dodge stratus?id do this jump it again drive it to the nearest shop and have it tested take only a minute most dont charge to test the battery and charging system even auto zone is a good place just dont shut it off could it be that the battery cables are dirty or loose.... what about the belts old dry loose is the battery bad then is it the alternator... id have it tested first to know whats bad and in most cases id do the work my self..... some are a pain some are not but they are all do able at home.... but no guessing.... it will cost you more fixing things that dont need itHow difficult is it to change the alternator on a 2002 dodge stratus?This might help. I wrote an article on eHow the other day to change the alternator in a dodge caravan. It's pretty general. Here is the link....... http://www.ehow.com/how_2288299_replace-

How to change the alternator in a 1993 Saturn SC2?

My alternator recently died and i was wondering if anyone knows how to replace it.How to change the alternator in a 1993 Saturn SC2?Sure, take the negative off the battery, take the belt off, take the wires going to alternator off, remove bolts holding it on, reverse procedure to re-install, pretty easy.How to change the alternator in a 1993 Saturn SC2?pretty easy, except it has to come out through the wheel well which is a painHow to change the alternator in a 1993 Saturn SC2?I have a 92 saturn and obvoiusly these other guys have never seen where the alternator is on the saturn...

I have been rebuilding and fixing cars for 20 years and when the alternator on my wifes car went I looked at it and took it in to the shop and had them do it, it took 2 hours labour , plus the cost of the alternator. the alternator is on the passenger side of the car near the rear of the engine, on the bottom . the job is done one half from the top and 2/3 done from the bottom . so if you have a hoist and are use to working on cars you should be able to do it in about 4 to 8 hours. if your lucky, sometines its just better to take it to a shop,

hope this helps

How long to change an alternator?

Hey

How long do thnk it wd take to change an alternator in a small car? anyone know?How long to change an alternator?it depends on the car and engine. On my 95 Buick Regal 3.8L, it takes about 3 minutes because the alternator is right on top and you only have to remove 2 bolts. Now on a 95 Lumina with a 3.4L Twin Cam, it can take several hours because the alternator is mounted on the back side of the engine and down below the heads. That one you have to partially drop the engine cradle and remove the passenger side drive shaft. On a small car with a small engine, a reasonably inclined person should be able to change an alternator in less than an hour from start to finish.How long to change an alternator?It REALLY depends on the car...



And by that, I mean it could be anything from a 20 minute job to something that takes half the day or more.



It all depends on where the alternator is located and how hard it is to get to.How long to change an alternator?depends on the make of the car...imports can be a real pain in the azz!How long to change an alternator?A bit more than an hour considering jacking, removing the mud guard behind the wheel. If you have a box or something to rest the alternator on after you remove the bolts it makes it easier to remove the rear connections. Have your negative ground connection off of your battery.How long to change an alternator?What color is animal?....Get the point?....lift the hood and see whats involved...Do you have the proper tools and the basic knowledge....remember, disconnect the battery terminals as the first step...make sure you have a diagram of the serpentine belt routing if that applies...Its often the little things that make a job like this tough...are you sure you need an alternator?...Are you just guessing?How long to change an alternator?What kind of car? A V-6 Volkswagen takes 8 hours. Pull the entire nose, to the serpentine belts! An older Accord says to pull the axle. A Cavalier takes a half hour. My wife's Camry, about the same. Her turbo Eclipse, what a #$%^%26amp;! !How long to change an alternator?I had a 1985 Honda Accord that required the front axle to be disconnected at the steering knuckle to access the alternator.



But because my toolset was a better fit with the task of removing the braking system's master cylinder (the axle requires a BF wrench which I didn't have), that's how I acessed it.



All the while I did that repair, I wished that I could find the engineer(s) who put the alternator there and slap the beejeezuz out of them.How long to change an alternator?My man says approximately 30. . .There us only 2 or 3 bolts holding it on...Loosen bolts and remove the belt and the wires, you have it off...Get another alternator and reverse what you did before and you will have it back on, usually in less than 30 minutes and you will be on the road again. . . .

How difficult is it to change an alternator belt?

I have a 1998 BMW Z3. Is it difficult to change the alternator belt? I really don't know anything about car repair, but I'd like to avoid paying a mechanic to do something if I could easily do it myself.



If you have any how-to links, I'd greatly appreciate 'em.



thanks!How difficult is it to change an alternator belt?just google for %26quot;bimmer forums%26quot; or similar items. There are a bunch out there and very helpful. I do know those engines do have a certain technique to replacing them, but most BMW's are fairly simple. (I am not sure of the exact proceedures for a z3) They are just very different from US cars.How difficult is it to change an alternator belt?Ok , first its not the timing belt... your car has an auxillary belt driven alternator. Its not that difficult to do, just find the belt tensioner, loosen it and that should give you enough slack to pull it out. Beyond that I would suggest going to a parts house and buy a haynes or chilton's manual for your car. These will help you do almost anything you want to do to your car. hope this helps....good luck.

artificially inflated

medium hair cuts

How to change the alternator on a 96 Chevy?

1996 Chevy 3/4 ton 350. The old alternator has only 1 wire but the new alternator has 3. How do i change it?How to change the alternator on a 96 Chevy?First confirm the %26quot;new %26quot; part is the proper part.

Call parts supplier and tell them your question.



When you are ready to change the Alt. first step disconnect BATTERY.

Safety first.

Changing Alternator Belt On 1994 Lexus ES300?

Does Anyone Know Step By Step Instructions On How To Change? I Basically Need To Know If There Is A Tension-er Pulley, Or Do You Just Loosen Alternator And Change Belt?Changing Alternator Belt On 1994 Lexus ES300?If you can't tell by looking at it maybe you should get a mechanic.

How to change alternator on vectra sri on a s reg 2.0l ?

Best find a repair manual for that car.

How to change alternator?

my mate's car wont start she had to call out recovery because i was unavailable to go jump her, she did unfortunately get another friend to do it but they managed to melt the leads whoops defo went wrong connecting the leads well cut a story short recovery bloke said she will need a new alternator, what would be the costs of having this repair done at a garage, or how would i go about changing it myself if i were to get the part im pretty niffy with my hands and do quite a lot of work on me own carHow to change alternator?Garages can have a right old field day with alternators and regularly do! Charging literally anything up to 300!



I wouldn't even get a new unit - get the blown one fixed. They are pretty much infinitely repairable. Check out the yellow pages under auto-electrics etc. There are people in most areas who specialise in just alternators, dynamos and magnetos etc.



They are only a real pain to change on some modern cars where they are buried under other components.



-|--)How to change alternator?It's fairly simple to change out an alternator. There are typically 1-2 bolts, and 1-2 wire connections (usually a cable held on with a nut on a stud, and an electrical connector). The alternator is usually toward the top of the engine, making it pretty easy to get to.How to change alternator?yes you can do it, but i recommend buying a cheap set of sockets and end wrenches,and from the sounds of your typoaccent,metric.read any instructions in the box.sometimes there are special replacement parts or special instructions.

How to change alternator for a 2002 Pt Cruiser?

We are having problems with our pt starting. My boyfriend has talked to a mechanic and it looks like it is the alternator but the mechanic needs the alternator to test it. Well our car is stuck at the house and doesnt start so my boyfriend is trying to take off alternator himself. It has been hard for him since the alternator is buried deep under all kinds of stuff so he thought it would be easier to get to it by going under the car. Even that has been a task to get it out. is there and easier way to get that alternator out? Help!How to change alternator for a 2002 Pt Cruiser?Charging the battery might be the easiest if you can. Otherwise, to take out the Alternator, the way to do that is through the passenger side wheel well. You can find instructions with pictures by going here;

http://www.autozone.com/shopping/repairG

and enter your year, make, model and engine. (if you don't know which you have, it doesn't really matter) Then click the link for %26quot;Engine Electrical%26quot;, and it's the first section that pops up. You can click on the pictures to enlarge them.



Navigate back to the %26quot;Steering%26amp;suspension%26quot; section for help with the lower control arm. Like I said, a lot easier to just charge the battery and drive it to the mechanic if you can.How to change alternator for a 2002 Pt Cruiser?Easiest is to charge the battery -you can do this with jumper cables and a running car. Then crank the Petey up. If will now run to Florida if you do not run radio, heater, lights etc. Drive it to mechanic and let him check it out and fix it.How to change alternator for a 2002 Pt Cruiser?The PT utilizes a generator. I would recommend that you use a service guide if you attempt this procedure. It contains numerous illustrations and instructions for the sub procedures mentioned below.

Generator



Removal - 2.4L Turbo



The generator is located above the oil filter and axle shaft.



1. Disconnect the negative battery cable.

2. Remove the 2 bolts from the top of the heat shield on the generator.

3. Remove nut from the upper T-bolt adjustment bracket.

4. Raise vehicle and support.

5. Remove the right front wheel.

6. Remove the accessory drive splash shield.

7. Remove the lower heat shield bolt.

8. Remove the generator heat shield.

9. Unplug the field circuit from the generator.

10. Remove the B+ terminal nut and wire.

11. Loosen the accessory drive belt t-bolt.

12. Remove the pencil strut.

13. Loosen the lower generator pivot bolt.

14. Remove the generator belt, refer to the Cooling section for more information.

15. Remove the axle retaining nut.

16. Remove the lower control arm from the steering knuckle.

17. Remove the 2 bolts for the axle shaft bearing support.

18. Remove the axle shaft assembly. Put a container under the transmission to catch the transmission fluid from the transmission.

19. Remove the generator from the lower mounting bracket and set generator to the side.

20 . Remove the lower mounting bracket for the generator.

21. Remove generator through the axle shaft hole.



Installation - 2.4L Turbo



1. Install generator through the axle shaft hole in wheel well.

2. Put generator on upper t-bolt and loosen install the nut.

3. Install the lower mounting bracket for the generator to the block and tighten bolts to 54 N-m or 40 ft./lbs.

4. Loose install the lower pivot bolt for the generator.

5. Install the B+ terminal nut and wire and tighten nut to 11.3 N-m or 100 in./lbs.

6. Plug in the field circuit to the generator.

7. Install the axle shaft assembly.

8. Install the 2 bolts for the axle shaft bearing support and tighten bolts to 54.2 N-m or 40 ft./lbs.

9. Install the axle shaft into the steering knuckle.

10. Install the lower control arm to the steering knuckle and install the bolt and tighten bolts to 94.9 N-m or 70 ft./lbs.

11. Install the axle retaining nut and tighten nut to 244 N-m or 180 ft./lbs.

12. Install and tension the generator belt, refer to the Cooling section for more information.

13. Tighten the accessory drive belt t-bolt and tighten nut to 54 N-m or 40 ft./lbs.

14. Tighten the lower generator pivot bolt and tighten bolts to 54 N-m or 40 ft./lbs.

15. Install the pencil strut.

16. Install the generator heat shield.

17. Install the lower heat shield bolt and tighten bolt to 54.2 N-m or 40 ft./lbs.

18. Install the accessory drive splash shield.

19. Install the right front wheel.

20. Lower vehicle.

21. Tighten nut to the upper adjustment bracket and tighten to 25 N-m or 18 ft./ lbs.

22. Install the 2 bolts to the heat shield on the generator and tighten bolts to 4.5 N-m or 40 in./lbs.

23. Connect the negative battery cable.

find a cute duvet cover

how to hang out with a girl

99 Volvo v70 XC- Change alternator

Does anyone know where I can get info/instructions online on how to replace a bad alternator in 99 Volvo V70 XC ?



Thank you99 Volvo v70 XC- Change alternatorGoogle alternator 99 Volvo

How to change alternator / release serpentine tension on tensioner pulley 92 LeBaron Conv 3.0L V6?

I need to change alternator 92 LeBaron. 1st time doing this on a Chrysler, 2nd time ever on any kind of car. I can't see what I'm doing, so will be working mostly by feel. How do I find which is tensioner %26amp; release tension on the tensioner pulley. Please add any additional tips a newbie should know for removing/installing alternator %26amp;/or serpentine in 3.0L v6 92 Base model LeBaron.How to change alternator / release serpentine tension on tensioner pulley 92 LeBaron Conv 3.0L V6?Push the belt in between any two pulleys, while watching with a flashlight. The one that moves when you push the belt in is the tensioner (the rest are stationary). Some tensioners have a hex, a square tab or a square hole that you grab with a socket and ratchet(or breaker bar), a crescent wrench, or a 1/2 inch square drive breaker bar or ratchet handle respectively. Check to make sure there is a pulley diagram before you remove the old belt. If there isn't, draw one because it can be confusing sometimes. Insert the correct tool and pull away from the belt on the circumference of the pulley. Flip the belt off. Then reinstall the new one.How to change alternator / release serpentine tension on tensioner pulley 92 LeBaron Conv 3.0L V6?your alternator pulley itself might be the tension pulley. take the bolts off the alternator and wiring and put new alternator in. you need a big pry bar and probably another person. hook up the belt and have someone pry on the bar and alternator pulley to put tension on the belt, then at the same time tighten the bolts on your alternator

I need to know how to change alternator on a 1994 ford probe?

locate the alternator.



disconnect the battery - negative (ground) wire first - VERY important.



unplug the connector(s) at the alternator.



Remove the bolts (usually one above and one below) holding the alternator in place.



Un thread the alternator from the belt.



Remove, take to auto-parts store to trade for replacement.I need to know how to change alternator on a 1994 ford probe?Your best bet if you do not know how already is to buy a Chilton's manuel, they are sold at almost all auto parts stores and more than likey, you will use it more than you think. However, it should just be disconnect the battery, discount the wiring harness going to the alternator, unbolt the alternator and take off the belt off of it, then do the reverse to put it back on. But I would still get the Chilton's.I need to know how to change alternator on a 1994 ford probe?Alternators are pretty simple... I've done them on a Probe GT but you never said which probe, pretty much the same either way though...



-Disconnect neg. battery cable



-Raise and support the passenger side of the car



-Remove the passenger wheel



-Remove the plastic splash sheld on the passenger side, few screw fasteners and 10mm bolts



-Remove the alternator belt

--Locate the idler pulley (the one that is JUST a pulley, nothing else)

--Loosen the pulley bolt

--Turn the long bolt going through the pulley bracket to loosen the belt

--Remove the belt



-Remove the wire harness from the front side of the alternator



-Remove the ground wire from the front side of the alternator (it's a nut that should be covered with a plastic shield)



-Remove the 2(maybe 3?) bolts holding the alternator



-Remove the alternator from underneath the car



Install is just reverse of that. Getting it out can be a pain, I think on my old GT I took the A/C compressor off of it's bracket and supported it to the side so that I had a little more room. Hope it helpsI need to know how to change alternator on a 1994 ford probe?the car is not worth the cost of a new alternator... i say junk that ford

Change alternator in 98 Mazda 626?

I am trying to figure out how to change an alternator in a mazda 626. There isn't enough room on the side to get to it and the frame is in the way so I cant go thru the wheel well. Any ideas that are cheap?Change alternator in 98 Mazda 626?Is it an inline 4 cylinder? I just loosened it all the way and jammed my arm in there with a size 12mm (i think) wrench and got the bottom bolt out. After that it is easy.Change alternator in 98 Mazda 626?if i remember it is on the bottom so the best thing to do would be to take the motor mount off and let it drop a little bit that should give you enough room but you may need to take the axle out

How hard is it to change alternator on nissan serena lx d 6 seater?

the engine is under the front seats ive just bought this old banger so i dont now much about it yet. i am a electrician so am handy,would i need any specialist tools

cheersHow hard is it to change alternator on nissan serena lx d 6 seater?alt. is a wlk in the park, my wife is able to do that no problemHow hard is it to change alternator on nissan serena lx d 6 seater?Simple job, I am an auto electrician too. Loosen the tension nut to remove the belt from the pulley. Unplug the electrical connections, next remove the mounting bolts and the alternator is out. Install in the reverse order

tvs

ho do i go about starting

How easy is it to change alternator on 03 plate ford ka, looks a nightmare?

it's a right pain to do. most cases you have to remove the headlight, and sometimes the bumper has to be removed also. some of the bolts are in almost impossible to get at places, typical of ford. it may be better to go to a garage if you are short of time. sorry couldn't be of more help.How easy is it to change alternator on 03 plate ford ka, looks a nightmare?ha ha not much room is thier ... no prob with little hands ...



should take you about 45mins .. you need wobbley sockets to get in behind the case'n .. if you have none get some or leave it .. you need 10mm spanner 13mm spanner and 13mm wobbley socket ...How easy is it to change alternator on 03 plate ford ka, looks a nightmare?Its a nightmare, headlamp out think you have to move the bumper as well, we have done 1 in work took one of the fitters forever to change the alt

Change Alternator 1998 GMC Sonoma?

Ok, so my alternator went out last night while helping a friend move.



How hard are these things to change? Is it simply just disconnecting the battery, taking off the belt, disconnecting the ground and positive wire from the alternator itself, removing the bolts and you're good to go? Or what?Change Alternator 1998 GMC Sonoma?Do not disconnect the battery, just make sure the key is off, it could erase the code to the radio and possibly other computer functions. Just release the tension on the belt tensioner enough to get the alt out, reverse to install, it isn't hard but I have seen people remove the tensioner when all you have to do is pull down on the spring loaded nut holding it on the pulley, good luck.Change Alternator 1998 GMC Sonoma?Yep. It's pretty easy.



Just make sure you connect the negative battery cable AFTER you connect the positive.Change Alternator 1998 GMC Sonoma?that about it it just doin itChange Alternator 1998 GMC Sonoma?DO disconnect the battery. (neg cable is enough.)Change Alternator 1998 GMC Sonoma?That's pretty much all there is to it. You only need to disconnect the negative battery cable, not both.Change Alternator 1998 GMC Sonoma?Yes you have it down real good just do as you said and you are good to go , Good luck

How to change alternator on ford fiesta?

Anyone got a diagram of how to change the alternator on a 1994 Fiesta 1.8D?? A scanned copy out a workshop manual would be helpful!!



ThanksHow to change alternator on ford fiesta?Go to your local auto parts store and spend some money (usually $25-$30) on a repair manual for your car. If your a do it yourselfer then the repair manual is a must. It will give you all the information you need to do anything the car needs from wiring diagrams, troubleshooting sequences, and how to test anything on the car. GOOD LUCK!!How to change alternator on ford fiesta?www.autozone.com They have a how To Fix Area,Check it Out

How to change alternator belt in 96 integra ls?

i know theres a bolt somewher eto be loosened so u can move the belt, but where? what size is it?How to change alternator belt in 96 integra ls?Do you have your manual its in there.How to change alternator belt in 96 integra ls?Loosen the alternator mounting bolts then you should be able release the tension on the belt by turning a long bolt. The long bolt swings out the alternator increasing the tension on the belt. You don't need to take any of the bolts completely off just enough to be able to remove the belt. Installation would be in the reverse order. Not sure the size, most Acura/Honda bolts are 10mm, 12mm 14mm 19mm 17mm

How dow you change alternator on combo van?

Is it easy or hard to change Alternator on a 2000 combo van. do i need any special toolsto take fan belt off.How dow you change alternator on combo van?no if it has a self tensioner then a 15 mm spanner will do the job

rent rates for central pa

web hosting providers